HazMat Tool — substance information

Titanium trichloride mixtures

HMT May 2026

UN / ID: UN 2869
Hazard class: 8
Packing group: II (multiple — see tabs)
ERG guide: ERG 157
Special provisions: SP A7, SP IB8, SP IP2, SP IP4, SP N34, SP T3, SP TP33
Source: 49 CFR §172 (2026/05)

Spot an error in this entry?

On this page

Titanium trichloride mixtures

Emergency Response Guide No. 157

Hazardous Materials Table

Source: 49 CFR §172 (2026/05)

Packing group II
Packing group III

(3) Hazard Class

8
Corrosive liquids

(7) Special Provisions (§172.102)

×Note:
Special provisions may be very complex. The extracts are taken from 49 CFR §172.102. Please be careful with the information, as necessary, additional conditions may be applied that are not written here. Please check the original source and report bugs.

Steel packagings must be corrosion-resistant or have protection against corrosion.

Browse special provision A7

IB8

Authorized IBCs: Metal (11A, 11B, 11N, 21A, 21B, 21N, 31A, 31B and 31N); Rigid plastics (11H1, 11H2, 21H1, 21H2, 31H1 and 31H2 ); Composite (11HZ1, 11HZ2, 21HZ1, 21HZ2 and 31HZ1); Fiberboard (11G); Wooden (11C, 11D and 11F); Flexible (13H1, 13H2, 13H3, 13H4, 13H5, 13L1, 13L2, 13L3, 13L4, 13M1 or 13M2).

Browse special provision IB8

IP2

When IBCs other than metal or rigid plastics IBCs are used, they must be offered for transportation in a closed freight container or a closed transport vehicle.

Browse special provision IP2

IP4

Flexible, fiberboard or wooden IBCs must be sift-proof and water-resistant or be fitted with a sift-proof and water-resistant liner.

Browse special provision IP4

N34

Aluminum construction materials are not authorized for any part of a packaging which is normally in contact with the hazardous material.

Browse special provision N34

Minimum test pressure (bar)	2.65
Minimum shell thickness	§ 178.274(d)(2)
Pressure-relief requirements	Normal
Bottom opening requirements	§ 178.275(d)(2)

Browse special provision T3

TP33

The portable tank instruction assigned for this substance applies for granular and powdered solids and for solids which are filled and discharged at temperatures above their melting point which are cooled and transported as a solid mass. Solid substances transported or offered for transport above their melting point are authorized for transportation in portable tanks conforming to the provisions of portable tank instruction T4 for solid substances of packing group III or T7 for solid substances of packing group II, unless a tank with more stringent requirements for minimum shell thickness, maximum allowable working pressure, pressure-relief devices or bottom outlets are assigned in which case the more stringent tank instruction and special provisions shall apply. Filling limits must be in accordance with portable tank special provision TP3. Solids meeting the definition of an elevated temperature material must be transported in accordance with the applicable requirements of this subchapter.

Browse special provision TP33

(8) Packing Authorizations (§173.***)

(8A) Exceptions	154	see 49 CFR §173.154
(8B) Non-bulk	212	see 49 CFR §173.212
(8C) Bulk	240	see 49 CFR §173.240

(9) Quantity Limits

(9A) Passenger aircraft/rail	15 kg
(9B) Cargo aircraft only	50 kg

(10) Vessel stowage

(10A) Location

Stowage category “A” means the material may be stowed “on deck” or “under deck” on a cargo vessel or on a passenger vessel.

Source: 49 CFR §172.101(k)

(10B) Other

40	see 49 CFR §176.84
53	see 49 CFR §176.84
58	see 49 CFR §176.84

Source: 49 CFR §176.84

(3) Hazard Class

8
Corrosive liquids

(4) Identification number

UN 2869

(5) Packing Group

III

Comparison View of PG

(6) Labels

(7) Special Provisions (§172.102)

Steel packagings must be corrosion-resistant or have protection against corrosion.

Browse special provision A7

IB8

Browse special provision IB8

IP3

Flexible IBCs must be sift-proof and water-resistant or must be fitted with a sift-proof and water-resistant liner.

Browse special provision IP3

N34

Aluminum construction materials are not authorized for any part of a packaging which is normally in contact with the hazardous material.

Browse special provision N34

Minimum test pressure (bar)	1.5
Minimum shell thickness	§ 178.274(d)(2)
Pressure-relief requirements	Normal
Bottom opening requirements	§ 178.275(d)(2)

Browse special provision T1

TP33

Browse special provision TP33

(8) Packing Authorizations (§173.***)

(8A) Exceptions	154	see 49 CFR §173.154
(8B) Non-bulk	213	see 49 CFR §173.213
(8C) Bulk	240	see 49 CFR §173.240

(9) Quantity Limits

(9A) Passenger aircraft/rail	25 kg
(9B) Cargo aircraft only	100 kg

(10) Vessel stowage

(10A) Location

Stowage category “A” means the material may be stowed “on deck” or “under deck” on a cargo vessel or on a passenger vessel.

Source: 49 CFR §172.101(k)

(10B) Other

40	see 49 CFR §176.84
53	see 49 CFR §176.84
58	see 49 CFR §176.84

Source: 49 CFR §176.84

Packing group comparison

Multiple packing groups apply to this entry. See assignment criteria in 49 CFR §173 Subpart D. Details are in the tabs above; differences are highlighted.

	PG II	PG III
1
2	Titanium trichloride mixtures	Titanium trichloride mixtures
3	8	8
4	UN 2869	UN 2869
5	II	III
6	8	8
7	A7, IB8, IP2, IP4, N34, T3, TP33	A7, IB8, IP3, N34, T1, TP33
8A	154	154
8B	212	213
8C	240	240
9A	15 kg	25 kg
9B	50 kg	100 kg
10A	A	A
10B	40, 53, 58	40, 53, 58

Segregation chart for load, transport, and storage

This chart shows whether loading, transport, or storage with other hazard classes is permitted, prohibited, or restricted. Based on 49 CFR §177.848.

Note: In this segregation and separation chart are HazMat of hazard class 8 considered depending if there are liquid. Currently HazMat Tool is not able to to check if a HazMat is liquid or not. Therefore it is assumed as liquid. See PHMSA Interpretation #09-0252.

Hazard class	8	7	6.1	5.2	5.1	4.3	4.2	4.1	3	2.3B	2.3A	2.2	2.1	1.6	1.5	1.4	1.3	1.1/1.2
1.1/1.2
1.3
1.4
1.5
1.6
2.1
2.2
2.3A
2.3B
3
4.1
4.2
4.3
5.1
5.2
6.1
7
8

	Must not be loaded, transported, or stored together in the same vehicle or facility.
	May be loaded, transported, or stored together.
	May be loaded, transported, or stored together only with restrictions.

Similar substances

UN / ID	Proper shipping name	Hazard class
UN 1352	Titanium powder, wetted with not less than 25 percent water (a visible excess of water must be present) (a) mechanically produced, particle size less than 53 microns; (b) chemically produced, particle size less than 840 microns	4.1
UN 2441	Titanium trichloride, pyrophoric or Titanium trichloride mixtures, pyrophoric	4.2
UN 2878	Titanium sponge granules or Titanium sponge powders	4.1
UN 2546	Titanium powder, dry	4.2
UN 3174	Titanium disulphide	4.2
UN 1871	Titanium hydride	4.1
UN 1838	Titanium tetrachloride	6.1